CyberOptics to Exhibit at SEMICON Japan


Reading time ( words)

CyberOptics Corporation announces it will showcase its next-generation Airborne Particle Sensor technology (APS2) with an extended particle size range at the upcoming SEMICON Japan in Tokyo, which will be held from December 14-16, 2016. CyberOptics will be in Booth 4605.

CyberOptics' APS2 portfolio speeds equipment set-up and long-term yields in semiconductor fabs by wirelessly monitoring airborne particles in real-time. The next-generation APS2 provides even greater versatility, with the industry-leading accuracy and sensitivity valued by semiconductor fabs and equipment OEMs worldwide.

Both the WaferSense and ReticleSense Airborne Particle Sensors (APS2, APSR and APSRQ) can measure small and large particles. The new large particle detecting and measurement functionality covers a range of sizes with four bins for particles larger than 2, 5, 10 and 30 microns.

"We're excited to demonstrate our APS2 devices with large particle capability in Japan, where the world’s largest installed fab capacity is over 4.1 million (200mm equivalent) wafers per month," said Yukinobu Hayashi, Sr. Field Applications Engineer, CyberOptics. "We've added this desired functionality to our devices that are recognized as the Best Known Method for wireless airborne particle sensing in semiconductor fabs."

At SEMICON Japan, CyberOptics will also demonstrate its WaferSense and ReticleSense Auto Multi Sensors (AMS/AMSR) that measure leveling, vibration, and relative humidity (RH) in an all-in-one wireless real-time device. The thin and light form factor enables the AMS to travel through virtually any tool and the AMSR can capture multiple measurements in all locations of the reticle environment. The all-in-one devices are yet another way to increase yield and reduce downtime in semiconductor environments.

About the WaferSense and ReticleSense Line

The WaferSense measurement portfolio including the Auto Leveling System (ALS), the Auto Gapping System (AGS), the Auto Vibration System (AVS), the Auto Teaching System (ATS), the Airborne Particle Sensor (APS), the advanced Airborne Particle Sensor (APS2) and the new Auto Multi Sensor (AMS) are available in various wafer shaped form factors depending on the device, including 150mm, 200mm and 300mm wafer sizes. The ReticleSense measurement portfolio including the Airborne Particle Sensor (APSR & APSRQ) and next-generation APS2, the Auto Leveling System (ALSR) and the Auto Multi Sensor (AMSR) are available in a reticle shaped form factor.

About CyberOptics

CyberOptics Corporation is a leading global developer and manufacturer of high precision sensing technology solutions. CyberOptics sensors are being used in general purpose metrology and 3D scanning, surface mount technology (SMT) and semiconductor markets to significantly improve yields and productivity. By leveraging its leading edge technologies, the company has strategically established itself as a global leader in high precision 3D sensors, allowing CyberOptics to further increase its penetration of its key vertical segments. Headquartered in Minneapolis, Minnesota, CyberOptics conducts worldwide operations through its facilities in North America, Asia and Europe.   

Share

Print


Suggested Items

SMTA Europe Solder Finish Webinar Addresses Defects Causes and Cures

12/14/2020 | Pete Starkey, I-Connect007
“What is your most common PCB problem?” A survey conducted by Bob Willis had revealed finish solderability to be the predominant contender, and it was clear that the choice of solderable finish applied to surface mount boards could have a significant effect on the assembly yield and cost of the final circuit. SMTA Europe organised an informative and enlightening webinar this month entitled “Guide to PCB Solder Finishes—Process Defects Causes and Cures,” with soldering specialist Bob Willis as presenter.

SMTA Europe Webinar: What Is a Good Solder Joint, and How Can Solder Joints Be Tested?

11/18/2020 | Pete Starkey, I-Connect007
What is a good solder joint? And how can they be tested not only for purposes of process characterisation, optimisation, monitoring, and control but also for ensuring their long-term reliability? Pete Starkey details a webinar organised by the Europe Chapter of SMTA that was presented by Bob Willis, an expert in soldering, assembly technologies, and failure analysis.

Reducing Flux Splatter in Sensors and Camera Modules

10/30/2020 | Jasbir Bath, Shantanu Joshi, and Noriyoshi Uchida, Koki Solder America And Koki Company Limited
With the increased use of electronics in new technology areas, flux formulations are being developed to address the new and existing requirements. For sensors and camera modules used for Advanced Driver Assistance System (ADAS) and internet of things (IoT) applications, there is a demand for no-clean flux formulations in lead-free solder paste, which can reduce flux splattering during reflow.



Copyright © 2021 I-Connect007. All rights reserved.