Seika Machinery to Exhibit at IPC APEX EXPO 2017


Reading time ( words)

Seika Machinery Inc. will exhibit in Booth #2409 at the 2017 IPC APEX EXPO, scheduled to take February 14-16, 2017 at the San Diego Convention Center in California. Seika will showcase a complete line up of leading-edge equipment, including the McDry HM-100BNF N2 Auto-Purge Model, Sawa Ecobrid SC-AH100 Fully Automatic Low-VOC Stencil Cleaner, Sayaka CT23NJ PCB Router, HIOKI FA1240 Flying Probe Tester, DEN-ON RD500V, UNITECH UC-250M-CV PCB Board Cleaner, MALCOM RCX Series and PCU-02V Spiral Viscometer.

The new McDry HM-1001BNF N2 Auto-Purge Model features an ultra-low humidity rapid dehumidication drying unit. With an RH level of just one percent, the system features automatic nitrogen purge upon opening/closing of doors. The ESD safe system also offers a power saving mode to reduce electricity costs.

The Sawa Ecobrid SC-AH100 Fully Automatic Low-VOC Stencil Cleaner provides a 66 percent reduction in CO2 emissions and energy consumption over the previously fully automatic cleaning system offered as well as a huge reduction in running costs. Additionally, the system cleans and dries in just ten minutes or less.

Sayaka CT23NJ PCB Router provides stress-free depanelization along with a fixture-based highly efficient dust vacuum system. In addition to clean and precise depanelization for densely populated PCBs, the router features advanced image-processing software with point-and-click operation for programming router paths.

The HIOKI FA1240 Flying Probe Tester provides a variety of benefits compared to conventional testing machinery. Some of these benefits include jig-less inspection for quick setup, and the proficient testing of mis-mounted components, faulty components, and poor contacts.

The DEN-ON RD500V series rework station is continually being upgraded to meet the latest electronics market needs and fast progress of technology. The RD-500V that will be presented at the show features all the latest enhancements including the new multiple step drives for profiling and process creation.

Seika also will highlight the UNITECH UC-250M-CV PCB Board Cleaner. The UC-250M-CV takes all the features of the UC-250M and adds a dual cleaning feature using a combination of a brush roller with the silicone/adhesive cleaning rollers. The combination dual dust removal system assures better results than a single brush or adhesive roller system.

The MALCOM RCX Series Modular Reflow Oven Profiling System offers complete profiling of reflow ovens, including oven temperature, video imaging, O2 concentration and convection air velocity. It verifies that ovens are performing at optimal conditions, and enables users to troubleshoot problem areas.

The MALCOM PCU-02V Spiral Viscometer is designed for expensive material testing and analysis by obtaining the viscosity characteristics with only a 0.2cc sample. MALCOM’s unique Spiral Sensor provides continuous measurement of non-newtonian fluids with good repeatability.

About Seika Machinery, Inc.

Seika Machinery, Inc. (SMI) is a subsidiary of Seika Corporation, Japan and member of the Mitsubishi Global Group. SMI provides electronics manufacturers with advanced machinery, superior materials and engineering services.

Share

Print


Suggested Items

Driving Down Cost in the Supply Chain

04/08/2021 | Meghan Zou, EPOCH
Driving cost out of the supply chain goes beyond reduction of raw material cost. Though many of the manufacturers today concentrate on negotiation with their raw material supplier(s) the hidden cost of internal supply chain goes undetected. To address the cost of the entire supply chain we should not only look at direct material cost but also the cost of internal supply chain. At Epoch we looked at four areas in particular which include: planning/tracking, storage/delivery, inventory management, and supplier relationships.

5 Keys to Smart Process Success

01/28/2021 | Steve Williams, The Right Approach Consulting LLC
Smart factories require the core underlying processes to be connected and “talking” to generate the data necessary to make real-time process decisions, that is, the IIoT (Industrial Internet of Things). In a truly connected factory, an ongoing continuous dialog between machines, business processes, suppliers and customers is happening in the background. This dialog is not only interactive, but proactive, as a constant stream of real-time data is tweaking and adjusting processes to drive improvement. It also provides time-critical information on how processes are operating, supply chain pipeline, and delivery status updates—all based on data.

An EMS Perspective on Inventory Management

08/27/2020 | I-Connect007 Editorial Team
Foad Ghalili of Epoch International discusses the inventory management practices the company has in place between its two facilities in Fremont, California, and Dalian, China; and how upgrading to an electronic management system made maintaining a much larger inventory possible.



Copyright © 2021 I-Connect007. All rights reserved.