Evaluation of the Use of ENEPIG in Small Solder Joints

Reading time ( words)


The surface finish of a printed circuit board provides a number of functions, with impacts starting at the point of design and continuing through the life of the assembled product. Electroless nickel electroless palladium immersion gold (ENEPIG) is a surface finish that has been demonstrated to have a variety of benefits, and to be suitable for both SnPb and Pb-free circuit card assembly. Extensive testing of ENEPIG has demonstrated the reliability of this surface finish and resulted in the creation of an industry standard for its application: IPC-4556 Specification for Electroless Nickel/Electroless Palladium/Immersion Gold (ENEPIG) Plating for Printed Circuit Boards. When soldering to ENEPIG, all of the palladium is dissolved into the solder joint, and creates a palladium-rich region at the base (Pd source) of the solder joint. This palladium-rich microstructure can spall off, exhibiting a columnar shape. With ever decreasing size of parts used in electronics assembly, the size of the solder joints correspondingly continues to shrink, which causes the relative size of this palladium-rich microstructure to grow relative to the overall joint thickness. In this study, the impact of industry standard Pd thicknesses on thin solder joints is evaluated through shear testing.


ENEPIG is a multi-layer surface finish for circuit boards. For soldering, the gold and Pd are applied to protect the solderability of the underlying Ni, and they are ultimately dissolved into the solder joint. Excessive amounts of these metals in the solder joint can potentially cause weakness of the solder joint, impacting reliability.

There is an industry specification (IPC-4556) that describes the requirements for ENEPIG, and the finish has some use in the industry, but is limited due to availability and the increased cost of the printed board (PB) relative to other surface finishes. The plated layers of ENEPIG are very flat, as all plated surface finishes are relative to Hot Air Solder Leveling (HASL), which makes it advantageous for smaller PB design features. As electronic component packaging technology advances and parts get smaller, the PB must have finer features to attach these parts. This decrease in feature size typically drives a decrease in solder paste stencil thickness for effective solder release, resulting in smaller solder joint volume. As the solder joint size gets smaller, the thickness of the surface finish on the PCB remains constant, so that the relative volume of gold and palladium in the solder joint increases. ENEPIG has been demonstrated to have acceptable performance and reliability for many current packages and solder joint configurations, but some studies raise concerns for use of ENEPIG at high concentrations or in very small solder joints1.

Round robin testing for the development of the IPC-4556 specification included palladium thicknesses of up to 17.95 microinches (µin). A 0.005-inch-thick stencil was used with a 0.025-inch diameter SnPb solder sphere, resulting a solder joint containing approximately 0.17% Pd. Shear testing of the solder ball on pad resulted in both lifted pads and cohesive failure in the bulk solder.

IPC-7095C Design and Assembly Process Implementation for BGAs warns of reliability impacts from excessive and non-uniform intermetallic compound (IMC) layer growth. IPC-4556 mentions a 3% limit for gold and palladium, and other sources have identified 2% as a limit2, but these limits based on a percentage are misleading when applied to Pd. Gold can (and is desired to) disperse throughout a solder joint to minimize impact, but Pd tends to form a distinct and concentrated IMC layer above the Ni.

Palladium has a slower solubility rate in molten solder than other metals. During soldering, the tin-palladium intermetallic compounds (either PdSn3 or PdSn4) will rapidly grow in the form of a thick lamellar structure perpendicular to the original palladium surface. Solder, consisting of a lead-rich phase, will be present between the lamellae. Further aging of solder joint can result in the movement (spalling) of the tin-palladium layer into the bulk solder and likely leave tin-palladium crystals within the bulk solder.

ENEPIG has been found to be prone to brittle fractures. The tin-palladium layers that form directly above the nickel plating has been found to be brittle, although some studies indicate that this may be based on weakness of a phosphorus rich nickel layer, not necessarily the Pd intermetallics3. The presence of tin-palladium crystals within the bulk solder has not been well-documented in terms of the effect on solder joint integrity; however as a comparison, tin-gold intermetallic crystals in bulk solder have been shown to embrittle a solder joint, enabling fracture of the solder joint along the gold intermetallics. It has not been shown that Pd intermetallics can have a similar effect within the bulk solder, the typical failure is associated with brittle fracture at the PB pad.

Based on the initial formation of a thick lamellar Pd intermetallic structure above the Ni layer, a limit on Pd thickness may be more appropriate to prevent excessive intermetallic layer thickness. A higher Pd thickness leads to an increased interfacial IMC thickness, specifically when SnPb solder is used. A thin palladium layer should dissolve rapidly into molten solder and result in no detrimental effect on solder joint mechanical properties. A variety of Pd thickness percentages or thickness limits have been proposed, some of which are lower than the 12 µin limit in IPC-4556. One paper suggests a limit of 7.8 µin4, although one study found that Pd thickness as high as 20 µin had no impact on solder joint shear strength5.

In this study, PBs plated with a typical ENEPIG surface finish (per IPC-4556) will be assembled with a minimum amount of solder to create a very small solder joint where the Pd concentration becomes larger relative to the overall solder joint. Solder shear strength and solder joint analysis will be used to investigate the acceptability of using ENEPIG with SnPb solder in these very small solder joints.

Experimental Procedure

For assembly and testing, an existing test vehicle was selected for use with a small LGA package. Using an LGA package limits the solder volume in the solder joint since there is no contribution from a solder ball as there is in a BGA package, resulting in a higher Pd concentration in the solder joint. A small LGA package of 6 x 6 pad array was selected and will be installed at the four corners of a larger BGA footprint in a manner so that only the middle 4 x 4 array of pads on the part are soldered. This will be done to increase the quantity of data points for the shear test, and to limit the number of solder joints which will limit the shear force required to remove the part.

The test vehicles (24 total) were separated into four sets, with three of these sets going to three separate vendors (each of which used a different plating chemistry) for application of the ENEPIG finish, and the remaining set coated with HASL (control set). Once returned, the PBs were subjected to XRF for measurement of the tri-metal layer thicknesses. The data from these measurements is shown in Figure 2 (each vendor represented by a different color).

A stencil of 3 mil thickness was used for solder paste application. The apertures of the stencil were matched to the PB pads (as designed) at 14.8 mil diameter. Half of the assemblies were soldered using Sn63Pb37 solder of type 3 with RMA flux. The remainder of the assemblies were soldered using Sn62Pb36Ag2 solder of similar type and flux content.


Fabrication of the test vehicles was completed and it was determined that the solder mask thickness was greater than desired (approximately 3.5–4.5 mil compared to 1.0 mil pad thickness). This was discovered during PB fabrication, as the thickness of the solder mask interfered with board electrical testing and the HASL process. Additional boards were fabricated with thinner solder mask to enable the HASL process on the control units. PBs with ENEPIG surface finish were not replaced.

To read this entire article, which appeared in the January 2017 issue of SMT Magazine, click here.


Suggested Items

Passing the Test With SMTA’s Rob Boguski

09/14/2022 | Andy Shaughnessy, I-Connect007
I recently spoke with Rob Boguski, president of Fremont, California-based Datest and an SMTA vice president and board member. Rob explained why today’s test customers are asking for more information than the traditional pass/fail, offers a preview of SMTA International, and gives an update on SMTA’s planning strategy for the next five years.

Four Silver Linings in the Stormy Clouds of Pandemic, Supply Chain, and Inflation

09/14/2022 | Dr. Ronald C. Lasky, Indium Corp.
It may be difficult to see any bright spots in the current and recent economic situation. We have all experienced the devastation of the pandemic, supply chain issues, and most recently, inflation. However, as a senior technologist for an international materials supplier (Indium Corporation) and a professor of engineering at an Ivy League research university (Dartmouth College), I offer these four silver linings for those of us in the electronics industry.

Solder Paste Printing and Optimizations for Interconnecting Back Contact Cells

07/26/2022 | Narahari S Pujari and Krithika PM, MacDermid Alpha Electronics Solutions
The interdigitated back contact (IBC) is one of the methods to achieve rear contact solar cell interconnection. The contact and interconnection via rear side theoretically achieve higher efficiency by moving all the front contact grids to the rear side of the device. This results in all interconnection structures being located behind the cells, which brings two main advantages. First, there is no frontside shading of the cell by the interconnection ribbons, thus eliminating the need for trading off series resistance, losses for shading losses when using larger interconnection ribbons. Second, a more homogeneous looking frontside of the solar module enhances the aesthetics.

Copyright © 2022 I-Connect007. All rights reserved.