CyberOptics to Demo New 3D AOI, SPI and CMM Systems at IPC APEX EXPO


Reading time ( words)

CyberOptics Corporation announced plans to exhibit in Booth #2409 at the 2018 IPC APEX EXPO, scheduled to take place February 27 - March 1, 2018 at the San Diego Convention Center, California. Company representatives will demonstrate the new high-speed SQ30003D CMM, an extension of the MRS-enabled SQ3000 platform deemed best-in-class, the new SE3000 SPI system and QX250i double-sided AOI system.

The new SQ3000 3D CMM (Coordinate Measurement) system, powered by Multi-Reflection Suppression (MRS) technology utilizes CyberCMM, a new comprehensive software suite for coordinate measurement. In a lab or production environment, the MRS-enabled SQ3000 CMM system is extremely fast and highly accurate, with repeatable and reproducible measurements for metrology applications in manufacturing of a wide variety of products such as PCBs, semiconductors and consumer electronics.

CyberCMM, an extensive suite of CMM tools, provides 100 percent metrology-grade measurement on all critical points much faster than a traditional CMM, including coplanarity, distance, height and datum X, Y, to name a few. A fast and easy setup can be performed as compared to a slow, engineering resource-intensive setup that typically requires multiple adjustments with traditional CMMs. 

The new SE3000 SPI system is the very first SPI system to incorporate the industry-leading MRS sensor technology with a finer resolution for the best accuracy, repeatability and reproducibility – even on the smallest paste deposits. Combined with the award-winning, easy-to-use software, solder paste inspection has reached a new level of precision for the most stringent requirements.

Also on display, the QX250i simultaneous double-sided AOI system offers fast, flexible and high performance inspection for all applications, and is ideally suited for pre-reflow and selective solder inspection. The top and bottom high-resolution Strobed Inspection Modules (SIMs) with enhanced illumination provide a single platform for the inspection and defect review process that shortens the production line and drives approximately 50 percent productivity improvement.

About CyberOptics

CyberOptics Corporation is a leading global developer and manufacturer of high precision sensing technology solutions. CyberOptics sensors are being used in general purpose metrology and 3D scanning, surface mount technology (SMT) and semiconductor markets to significantly improve yields and productivity. By leveraging its leading edge technologies, the company has strategically established itself as a global leader in high precision 3D sensors, allowing CyberOptics to further increase its penetration of its key vertical markets. Headquartered in Minneapolis, Minnesota, CyberOptics conducts worldwide operations through its facilities in North America, Asia and Europe.

For more information, click here.

Share

Print


Suggested Items

Reducing Flux Splatter in Sensors and Camera Modules

10/30/2020 | Jasbir Bath, Shantanu Joshi, and Noriyoshi Uchida, Koki Solder America And Koki Company Limited
With the increased use of electronics in new technology areas, flux formulations are being developed to address the new and existing requirements. For sensors and camera modules used for Advanced Driver Assistance System (ADAS) and internet of things (IoT) applications, there is a demand for no-clean flux formulations in lead-free solder paste, which can reduce flux splattering during reflow.

IPC Standards Development: Business Challenges and an Inside View

10/28/2020 | Graham Naisbitt, Gen3 Systems
With increasing frequency, standardising the standards, such as ISO 9201, imposes certain rules that must be met to ensure “fair play” amongst the supply chain. There will be those familiar with hearing about “false positives/negatives” and “never trust the salesman,” so mitigating these is no easy task. However, there is the chance for each 5-30 Task Group to review industry requirements and set out the work program for the ensuing period. With that in mind, much of what follows is based on comments we learn about from our industry around the world, many of whom are not yet IPC members. Yes, this is a membership recruitment drive, unashamedly, as well as a search for volunteers willing to help create the standards of tomorrow.

How to Benefit From Robotic Soldering Processes

10/28/2020 | Pete Starkey, I-Connect007
Webinars are in vogue! But in Pete Starkey's experience, the master of the technical webinar with many years’ experience of delivering first-rate events is Bob Willis—electronics assembly specialist, soldering expert, and provider of training and consultancy in electronics manufacture. Here, Pete recaps Bob’s presentation on the upcoming robotic soldering experience.



Copyright © 2020 I-Connect007. All rights reserved.