Vehicle Electrification: Disrupting the Automotive Industry and Beyond

Reading time ( words)

Around the globe, governments are announcing mandates that will bring about the demise of the internal combustion engine. China has led the charge by requiring 8% of new vehicles on the road to be “new energy” or zero emission vehicles in 2018, a huge growth over the current 2–3% on the road today. Similar strong government regulations limiting the future of the internal combustion engine have passed around the world, and the importance and growth of the hybrid and fully electric automobile industry can’t be overstated.

Volvo has possibly taken the strongest stance of the automotive manufacturers by pledging to make only hybrid or fully electric cars by 2019 and committing to sell more than 1 million electric vehicles by 2025. “This announcement marks the end of the solely combustion engine-powered car,” said Hakan Samuelsson, president and CEO of Volvo, in a July 2017 statement. 

Although we have yet to witness such bold and aggressive challenges in Southeast Asia, the region is home to a fairly strong automotive industry. For instance, Thailand is the base country for many automotive OEMs, while the Philippines and Malaysia are the go-to destinations for supply chain vendors including component designers and manufacturers as well as semiconductors. This signals tremendous opportunities for the automotive industry in terms of autonomous vehicles and electrification. 

More than Electric Vehicles 

The move from internal combustion to hybrid and then fully electric power plants represents only the most visible portion of the aggressive growth of power electronics systems in vehicles. Electrification applies just as significantly 

to vehicle subsystems. As recently as 10 years ago, a fully mechanical coupling between the steering wheel and the front wheels was not unusual. The steering wheel connected to a shaft that connected to a rack-and-pinion system that turned the wheels, and even a more efficient hydraulic version of the system still maintained a mechanical coupling between the steering wheel and the tires. The story is similar for the accelerator pedal and manual transmission. 

The explosion of drive-by-wire technology throughout the modern vehicle has changed this paradigm. A sensor, a remote actuator, and multiple control systems have replaced the mechanical linkage. Instead of a direct connection between the steering wheel and the front tires, a sensor on the steering column now measures the angle of the wheel. An embedded controller then translates that measurement into an angle and sends the value to the vehicle’s communication bus. Elsewhere on the communication bus, another controller picks up the value, translates that into an angle of the wheel potentially based on vehicle speed and driver settings, and then commands an actuator to move the wheel to a desired angle. 

In many vehicles, a safety system sits in the middle of this drive-by-wire steering system to make sure the vehicle stays in the traffic lane and avoids obstacles in the roadway. As the number of power electronics subsystems in the vehicle grows, the automobile itself begins to look like an electrical microgrid with a common power bus connecting a growing list of sources and sinks of power, each managed by an independent embedded control system. 

The Broader Impact—Challenges 

Taking a slightly broader look at the implications of government automotive mandates, the exponential growth in electrification and the impending end of internal combustion engines represent a radical change in the infrastructure required to support the shift in vehicle power plants. A car with an internal combustion engine requires roughly 10 minutes at nearly any petrol station to fill up its tank for another 300 miles of driving. However, even with a dedicated supercharger, a similar pit stop requires at least an hour for a fully electric vehicle to charge. Even for the slow recharge associated with a daily commute, the required charging hardware needs some thought. For homeowners, installing an overnight charging station might be as simple as putting in a high-current circuit in the garage, but this becomes more complicated for a renter in a house or an apartment. If a car owner happens to live in a city and parks on the street, the concept of a home-charging station might be completely impossible.

The future of vehicle electrification from the prospective of the electrical utility, the cyclic demands based on the daily workforce schedule combined with the high-load demands of fast charging present significant new challenges for the electrical grid as well. If an entire workforce returns home at 5:00 p.m. and plugs in its electric vehicles around the same time, this shifts the timing of the typical peak demand on the grid and refocuses the regional peak consumption from heating or cooling toward transportation. On the larger scale of a gas station, a collection of the superchargers for fast charging will require an amount of energy like that of a medium-sized neighborhood.

To read the full version of this article, which appeared in the April 2018 issue of SMT007 Magazine, click here.


Suggested Items

MTV Offers Solder Paste Testing Solution

06/17/2020 | Nolan Johnson, I-Connect007
The miniaturization test vehicle (MTV) is a common benchmark test board that can gauge about 25 different paste properties and analyze how different solder pastes will perform in an assembly line. Chrys Shea details the work she’s done to develop and release the MTV.

This Month in SMT007 Magazine: How Engineers Can Use SPI Tools for Verification

05/06/2020 | Nolan Johnson, I-Connect007
Koh Young’s Ray Welch and Brent Fischthal detail how engineers can work with SPI tools to verify how small they can go in component size with their solder paste application, and how the company’s SPI equipment is helping not only to verify but also to help drive the development collaboration between solder paste and stencil printer manufacturers, and inspection tools and software.

The Convergence of 5G and Automotive

01/08/2020 | Barry Matties, I-Connect007
Karthik Vijay is head of the applications engineering team for customers in Europe at Indium Corporation. He spoke with Barry Matties about what EMS or assemblers for automotive should consider, as well as how he thinks 5G will affect the marketplace and manufacturing.

Copyright © 2023 I-Connect007 | IPC Publishing Group Inc. All rights reserved.