CyberOptics to Demonstrate AVLS3 and NanoResolution MRS Sensors at SEMICON Taiwan


Reading time ( words)

CyberOptics Corporation will exhibit at SEMICON Taiwan, September 18 to 20, 2019 at the Taipei Nangang Exhibition Center in booth # L0310. During the show, the company will launch its new WaferSense auto vibration and leveling sensor (AVLS3) with CyberSpectrum software and the new NanoResolution multi-reflection suppression (MRS) sensor for inspection and metrology in semiconductor applications.

At only 3.5mm, AVLS3 can travel with ease to most fab locations where a wafer travels. The chemically hardened glass (CHG) substrate enables smooth wafer handling and improved vacuum chucking.

With long-range wireless capability, AVLS3 combined with new, easy-to-use CyberSpectrum software, collects and displays both leveling and vibration data simultaneously for fast equipment set-up, alignment and real-time equipment diagnostics.

Additionally, for mid-end and advanced packaging inspection and measurement, CyberOptics will demonstrate the new proprietary NanoResolution MRS sensor technology that meticulously identifies and rejects multiple reflections caused by shiny components and mirror-like surfaces. Effective suppression of multiple reflections is critical for highly accurate measurements.

 “There is a dire need in the industry for highly accurate, 100% inspection of semiconductor advanced packaging applications, at a higher speed,” said Dr. Subodh Kulkarni, president and CEO, CyberOptics Corporation, “This is precisely the market we’ve designed the NanoResolution MRS sensor to address, with speeds 2 to 3 times higher than alternate technologies.”

Offering an unparalleled combination of high accuracy, high resolution and speed, MRS sensors are widely used for inspection and measurement in the SMT and semiconductor markets. The new 3-micron NanoResolution (X/Y resolution of 3 micron, Z resolution of 50 nanometer) MRS sensor enables metrology grade accuracy with superior 100% 3D and 2D measurement performance for features as small as 25-micron.

Further, it is two to three times faster than alternate solutions in the marketplace. With data processing speeds in excess of 75 million 3D points per second, the NanoResolution MRS sensor delivers throughput greater than 25 wafers (300mm) per hour. 100% 3D and 2D metrology and inspection can be completed simultaneously at high speed, versus an alternate, slow method that requires two separate scans for 2D and 3D, and only a sampling of a few dies of the 25 wafers.

This best-in-class MRS sensor technology that recently won the Best of the West award at SEMICON West, is ideally suited for the inspection of solder balls and bumps, copper pillars, and other wafer-level and advanced packaging applications where high precision and speed are needed.

About CyberOptics

CyberOptics Corporation (www.cyberoptics.com) is a leading global developer and manufacturer of high-precision 3D sensing technology solutions. CyberOptics’ sensors are used for inspection and metrology in the SMT and semiconductor capital equipment markets to significantly improve yields and productivity. By leveraging its leading edge technologies, the Company has strategically established itself as a global leader in high precision 3D sensors, allowing CyberOptics to further increase its penetration of key vertical markets. Headquartered in Minneapolis, Minnesota, CyberOptics conducts worldwide operations through its facilities in North America, Asia and Europe.

For more information, visit www.cyberoptics.com.

Share

Print


Suggested Items

Comparing Soldering Results of ENIG and EPIG Post-steam Exposure

09/11/2019 | Jon Bengston and Richard DePoto, Uyemura International USA
Electroless nickel immersion gold (ENIG) is now a well-regarded finish used to enhance and preserve the solderability of copper circuits. Electroless palladium immersion gold (EPIG), meanwhile, is a new surface finish also for enhancing and preserving solderability—but with the advantage of eliminating electroless nickel from the deposit layer. This feature has become increasingly important with the increasing use of high-frequency PCB designs whereby nickel’s magnetic properties are detrimental.

Solder Mask Evolves into a Truly Additive Process

09/09/2019 | John Fix, Taiyo America Inc.
The 5G era is creating quite a bit of work for many PCB engineers as the materials required to keep up with the speed, frequency, and latency requirements need to be defined and qualified. Solder mask, for example, now becomes a truly additive process. Read on to find out how and why.

Selecting the Proper Flex Coverlayer Material

09/06/2019 | Dave Lackey, American Standard Circuits
Coverlayers are polymer materials used to cover and protect the copper traces of the flex circuit product. There are a number of different options available for protecting the circuits, and they serve different design requirements in terms of cost, performance, and flexural endurance optimization. When specifying the choice, it is critical to call out not just the type of coverlayer material but also the thickness requirement. This can be very important in certain types of constructions, especially when a flex circuit will experience dynamic flexing during use.



Copyright © 2019 I-Connect007. All rights reserved.