Advanced Inspection Systems from MIRTEC at SMTA Guadalajara


Reading time ( words)

MIRTEC will exhibit at the SMTA Guadalajara Expo & Tech Forum, scheduled to take place October 2324, 2019 at the Expo Guadalajara. The MIRTEC team will showcase the all new MV-6 OMNI 3D AOI Machine and award-winning MS-11e 3D SPI Machine.

The MV-6 OMNI combines MIRTEC's exclusive 15 Mega Pixel CoaXPress camera technology with their proprietary OMNI-VISION 3D Digital Tri-Frequency Moiré technology to provide precision inspection of SMT devices on finished PCB assemblies. MIRTEC’s exclusive 15 Mega Pixel CoaXPress camera system is designed and manufactured by MIRTEC for use with its complete product range of inspection equipment. 

MIRTEC's proprietary Digital Tri-Frequency Moiré Technology, provides superior 3D inspection of SMT and through-hole devices up to 25 mm tall. This industry-acclaimed technology yields precise height measurement data used to detect lifted component and lifted lead defects as well as solder volume post reflow. Fully configured the new MIRTEC MV-6 OMNI machines feature four (4) 10 Mega Pixel Side-View cameras in addition to the 15 Mega Pixel Top-Down camera. There is little doubt that this new technology has set the standard by which all other inspection equipment are measured.

MIRTEC’s award-winning MS-11e 3D SPI Machine is configured with an exclusive 15 Mega Pixel CoaXPress camera system, providing enhanced image quality, superior accuracy and incredibly fast inspection rates.

The MS-11e uses dual -projection shadow-free Moiré phase shift imaging technology to inspect solder paste depositions on PCBs post screen print for insufficient solder, excessive solder, shape deformity, shift of deposition and bridging. The MS-11e uses the same robust platform as MIRTEC's MV-6 OMNI Series.

MIRTEC's total quality management system software, INTELLISYS also will be on display at SMTA International. This software suite promotes continuous process improvement by allowing manufacturers to track and eliminate defects on inspected assemblies.

About MIRTEC

MIRTEC is a leading global supplier of automated inspection systems to the electronics manufacturing industry.  For further information, please visit www.mirtec.com

Share

Print


Suggested Items

SMTA Europe Webinar: What Is a Good Solder Joint, and How Can Solder Joints Be Tested?

11/18/2020 | Pete Starkey, I-Connect007
What is a good solder joint? And how can they be tested not only for purposes of process characterisation, optimisation, monitoring, and control but also for ensuring their long-term reliability? Pete Starkey details a webinar organised by the Europe Chapter of SMTA that was presented by Bob Willis, an expert in soldering, assembly technologies, and failure analysis.

This Month in SMT007 Magazine: Test and Measurement in a Smart Factory

11/03/2020 | Nolan Johnson, I-Connect007
Nolan Johnson spoke with MIRTEC President Brian D’Amico about how the role of test and measurement equipment is changing in the smart factory and how shops can adjust to make use of the new technology. D’Amico shares this insight: “While approximately 90% of U.S. electronics manufacturers recognize the potential of Industry 4.0 to improve productivity, many are slow to adopt smart factory solutions within the manufacturing process.”

Reducing Flux Splatter in Sensors and Camera Modules

10/30/2020 | Jasbir Bath, Shantanu Joshi, and Noriyoshi Uchida, Koki Solder America And Koki Company Limited
With the increased use of electronics in new technology areas, flux formulations are being developed to address the new and existing requirements. For sensors and camera modules used for Advanced Driver Assistance System (ADAS) and internet of things (IoT) applications, there is a demand for no-clean flux formulations in lead-free solder paste, which can reduce flux splattering during reflow.



Copyright © 2020 I-Connect007. All rights reserved.