Latest iNEMI Roadmap Chapters Cover Ceramic Interconnect & Photovoltaics, Connectors, and Passive Components


Reading time ( words)

The International Electronics Manufacturing Initiative (iNEMI) has released three additional chapters from its 2019 Roadmap. The Ceramic Interconnect & Photovoltaics, Connectors, and Passive Components chapters are now available online, along with 13 additional chapters already published.

Chapter Highlights
Ceramic Interconnect & Photovoltaics — This chapter provides an update on several key ceramic interconnect technologies, such as thick film, high and low-temperature co-fired, thin film, pure copper metallization on ceramic, and lead-free thick film. It provides direction on industry and technology needs including design tool, material and processing developments and cost reduction opportunities to address future market expectations in terms of performance and cost. Innovative ceramic interconnection substrate technology is a key enabling technology for mobile device applications, future networks (e.g., 5G), and IoT devices and applications. In addition, the chapter updates on the status of the photovoltaic industry and includes a section covering crystalline silicon solar cell design, fabrication and testing.

Connectors — Providing comprehensive information about electronic connectors, this chapter includes an overview of the current situation as well as projected technology enhancements and challenges over the 10-year roadmap horizon. It presents business, component, and substrate trends, and the impact of these trends on the manufacturing processes for surface mount, part placement, wave and selective soldering, press-fit and rework/repair.

Passive Components — The Passive Components chapter discusses technology needs and recommendations for capacitors, resistors, magnetics and circuit protection components, which are the highest volume passive components in electronic devices. They support power management, signal conditioning, and protection of active devices. This chapter, which was developed in collaboration with the Electronic Components Industry Association (ECIA), presents four areas of common cross-cut requirements: (1) environmental compliance with rapidly changing regulatory requirements, (2) component sensitivity to board mount conditions, (3) increased customer sensitivity to non-graceful failure modes of components, and (4) issues with counterfeit components. It also focuses on the specific needs for passives components in key markets such as automotive, medical and high-end systems.

Now Available
The 2019 Roadmap is now available on the iNEMI website. It is free for iNEMI members and chapters are $500 each for non-members. Special pricing is available for non-profit organizations, including universities, research institutes and government agencies. For additional information: https://www.inemi.org/2019-roadmap-overview

For the 2019 Roadmap, chapters are being published in waves, with new chapters released every two to three weeks. The first four waves, already available online, included the following 13 chapters: Aerospace & Defense; Board Assembly; High-End Systems; Industrial Internet of Things; Mass Data Storage; Medical; MEMS & Sensors; Modeling, Simulation & Design Tools; Optoelectronics; Power Conversion Electronics; Semiconductor Technologies; Smart Manufacturing; and Sustainable Electronics.

About iNEMI
The International Electronics Manufacturing Initiative’s mission is to forecast and accelerate improvements in the electronics manufacturing industry for a sustainable future. The consortium is made up of more than 90 manufacturers, suppliers, industry associations and consortia, government agencies, research institutes and universities. iNEMI roadmaps the needs of the electronics industry, identifies gaps in the technology infrastructure, executes collaborative projects to eliminate these gaps (both business and technical) and stimulates standards activities to speed the introduction of new technologies. The consortium also works with government agencies, universities and other funding agencies to set priorities for future industry needs and R&D initiatives. iNEMI is based in Morrisville, North Carolina (in the Greater Raleigh/Research Triangle Park area). For additional information about iNEMI, visit http://www.inemi.org.

Share

Print


Suggested Items

Foundations of the Future: Get More Engaged in 2020

01/22/2020 | Charlene Gunter du Plessis, IPC Education Foundation
Since the inception of the IPC Education Foundation in January 2019, the mission remains to create connections between electronics manufacturers and supply chain companies, academia and the emerging workforce. In this debut column, Charlene Gunter du Plessis describes plans for engaging in 2020, including scholarships and more, and the IPC APEX EXPO 2020 STEM Student Outreach event.

CyberOptics Sensors: So Good That Their Rivals Use Them

12/20/2019 | Real Time with...productronica
Editor Nolan Johnson and Subodh discuss CyberOptics’ latest precision 3D systems, such as the SQ3000, which offers AOI, SPI and CMM functionalities. The inline CMM system includes top-of-the-line software for metrology grade measurements of critical points. Subodh points out that some of his competitors even utilize CyberOptics sensors in their equipment.

Global Political Turmoil Creating Uncertainties for the Industry

11/20/2019 | Chris Mitchell, IPC Vice President of Global Government Relations
From where I sit, representing the interests of electronics manufacturers and related companies around the world, I regret to say that the future of our industry—while bright overall—is fraught with uncertainties, from trade policy disputes to government leadership turnovers and economic and social megatrends. IPC is working with all governments and parties to overcome these uncertainties, but there is a lot to tackle.



Copyright © 2020 I-Connect007. All rights reserved.