Faster, More Precise Jet-dispensing in Microsystems Technology


Reading time ( words)

Miniaturization is making high demands of microsystems technology, requiring microdispensing to walk a fine line between speed and precision.

As miniaturization advances relentlessly, the components that need to be connected are becoming ever smaller and more delicate. At the same time, quality standards and the functionality of the materials are increasing. This development requires joining processes that can reliably fix the smallest of components. In many cases, bonding is the best solution to meet the requirements of the various materials and the tight installation space.

But bonding small components requires minute amounts of adhesive to be precisely applied, which is only possible with special dispensing processes like microdispensing. Zero-defect strategies can only be implemented for bonding processes if the dispensing quantities and positions can be maintained at an absolutely constant level.

What is more, microsystems technology is also being confronted with the task of further reducing costs. This essentially requires the production processes to be sped up, which is increasingly focusing attention on quicker dispensing processes for bonding.

The challenge for microdispensing technology is clear-cut: increasingly small amounts must be dispensed with increasing precision and in increasingly fast times.

The status quo in microdispensing

The physical characteristics of components, substrates and the materials to be dispensed can complicate the dosing process. As well as the high demands for accuracy, dispensing also represents a three-dimensional challenge. It is therefore absolutely necessary to make use of cameras to take measurements before and during this process. Even when this challenge can be overcome, there is still the possibility of undesirable dripping, which can displace the adhesive.

With its linear, volume-controlled dispensing, Häcker Automation GmbH already has a patented process in place that enables the highly precise application of extremely small quantities. A tappet in the dispensing device can be moved linearly up and down by a drive motor causing it to push on the sealing plug of the cartridge. The feeding motion of the tappet, which can be controlled in a defined way, dispenses a precisely determined volume of the fluid substance depending on the cartridge and dispensing-needle cross-section. Changes in the fill level of the cartridge and its internal pressure, or in the material viscosity or flow resistance are compensated for through a continual comparison between the actual and desired dispensing amount. With this control loop, a uniform process with a stable volume can be guaranteed over a long period of time.

Combining speed and precision

However, in the face of ever shorter product life cycles and payback times, precision and stability alone are not enough to gain a competitive edge. It is also a question of shortening cycle times by speeding up dispensing processes.

In order to meet the market demand for higher throughputs, Häcker Automation launched a collaboration with DELO Industrial Adhesives to combine the benefits of the linear, volume-controlled process with those of jetting, taking microdispensing to the next level. For this, Häcker Automation is integrating the DELO-DOT PN2 jet valve into its D-J30 dispenser module, which will enable two types of operation.

Delo1.jpg

Häcker and DELO are combining their expertise in a dispensing module (Photo: DELO)

For the first variant, needle-dispensing is retained. The integrated jet valve is used here as an opening and closing valve, preventing the medium from escaping unchecked. As a result, dispensing can be up to three times quicker. Thanks to the control loop described above, the application results can be highly precise and, above all, reproducible. It allows different material quantities to be dispensed at a constant level of precision over a long period of time.

To speed up the dispensing process still further, the two companies' second variant relies on open jetting, where the adhesive is applied without contact, i.e. without a needle. As the feed motion of the needle is no longer required, the dispensing speed also increases and cycle times are optimized further. In this operating mode too, the linear, volume-controlled process ensures that various volumes can be precisely and uniformly applied, with the focus here being on speed compared to the first option. What is more, tolerances for the component position along the z-axis are not important in this operating mode because, with jetting, the free-flowing drops of adhesive inherently always reach the substrate surface at its actual height. The risk of a collision between needle and component, which is ever present with needle-dispensing, is effectively precluded from the outset.

Delo2.jpg

Accuracy, reproducibility, speed – with a drop size of just a few hundred micrometers. (Photo: DELO)

Outlook

The two companies already have plans to investigate the operating conditions of this combined technology for a diverse range of new materials to make the benefits of jet dispensing available for a broad spectrum of applications.

Share

Print


Suggested Items

Video from productronica 2017: Mycronic Discusses Precision Jetting Systems

11/17/2017 | I-Connect007
From the show floor during productronica 2017, Clemens Jargon, VP of Global Dispensing at Mycronic, discusses with I-Connect007 Technical Editor Pete Starkey the company’s portfolio of precision jetting equipment, with particular reference to the speed and versatility of the MYSmart series.

RTW NEPCON South China: Vermes Discusses Piezo Technology in Microdispensing

09/12/2017 | Real Time With... NEPCON South China
During the recent NEPCON South China event in Shenzhen, Juergen Staedtler, CEO of Vermes Microdispensing GmbH, discusses their latest innovations in microdispensing, and how their piezo technology is addressing the trend towards miniaturization in PCB assemblies.

Shenzhen Axxon Discusses Acquisition and Dispensing Market Trends

06/02/2017 | Stephen Las Marias, I-Connect007
Ivan Li, general manager at Shenzhen Axxon Automation Co. Ltd (China), discusses their recent acquisition by Mycronic, as well as the latest developments in the dispensing market. Also discussed is the China market, and how the company is staying ahead of the increasing competition in the dispensing industry.



Copyright © 2019 I-Connect007. All rights reserved.