The Sum of All Parts: The Fabricator-Assembler Connection

Reading time ( words)

After discussing the relationship between PCB fabricators and those who design the boards (see my previous column ), it is imperative to do the same for the relationship between assemblers and fabricators. This brings about a whole new set of potential complications.

For example, a board manufacturer may not fully understand the scope of panel size limitations for the SMT line in question or if rails are needed on individual pieces/panels so that the pick & place machine has sufficient room to place the components that are close to the board’s edge. You may also have a situation where a component overhangs off the edge of a board. To be sure in can be placed, if in panel form, then the panel array will need additional space between boards so there is no interference of the part to the next board in the array.

Logistical Challenges

The supply of parts is a very crucial element of this relationship. Most assembly houses do not stock an inventory of components for the simple fact that it does not make business sense; every customer will require different parts from job to job and revision to revision. For the assembler to purchase and sit on various parts they think their customers might need is essentially just an increase in toxic, unusable assets that hurt the bottom line. You might have capacitors, resistors etc., with the exact value your customers need, but if it is not made by the manufacturer they desire or supplied by their preferred vendor, the assembler is left with an unusable part.

However, if a board house also has the ability to assemble, it lends to a number of advantages. First and foremost, the customer is able to rely on an accurate and unchanging quote from their manufacturer/assembler. Furthermore, when the customer is given a date on which their job will be completed, their job is actually completed on that date. They are not waiting to receive the bare board from one place and then send it out to another place to be populated—at which time the wait begins all over again. The speed of this process—end to end—is also accelerated significantly.

Packaging and Cleanliness

This in crucial in today’s market when customers expect their boards to be pristine and understandably so. The packaging and shipping processes can cause unnecessary cosmetic and damage to the board. The boards should be vacuum sealed with desiccant. Desiccant is vital to eliminate any moisture that can potentially absorb into the board in transit as well as sitting on the assembler’s shelf until they are assembled. In the case of immersion silver final finish, silver saver paper needs to be inserted between each board to keep the silver from oxidizing. ESD handling can also be a potential issue. When the board is manufactured and populated at the same location, however, you minimize the possibility of these and related errors occurring.

Uniformity of Process

Quality control can be greatly affected when separate entities are handling the manufacturing and assembly processes. Also, there is a great disconnect in the communication between the manufacturer and assembler. Some customers choose to be the ones to relay information between the two parties whereas others may simply choose to hand the ball off to the people working for them. The ideal scenario in this situation is a balance between those two scenarios where the input of the customer, manufacturer and assembler is taken into account and valued equally.

Similar to the designer-manufacturer relationship, the most comprehensive solution to this problem is the Total Concept. If manufacturing and assembling are done under the same roof, the space in which errors can occur is marginalized exponentially.

Although it seems like conventional wisdom, it is not always so. Simply put, the less distance there is between two processes, the less room for error.

Sam Sangani is president and CEO of PNC Inc.


Suggested Items

Board Pricing Challenges and Opportunities

08/24/2022 | Andy Shaughnessy, Design007 Magazine
The cost of everything is on the way up, and fabricators are feeling the squeeze. They may hesitate to raise their prices because they don’t want to scare off business, but what options do they have? We asked James Hofer, general manager of Accurate Circuit Engineering, to weigh in with his thoughts on this conundrum.

Catching Up with Prototron’s Lee Salazar: Sales in the New Frontier

07/12/2022 | Dan Beaulieu, D.B. Management Group
In the business world, salespeople arguably were the most affected by the pandemic. These professionals had to be the most creative when trying to ply their trade. They had to work from home, make phone calls in lieu of face to face, and learn how to use social media networks and newsletters. This was all to reach their customers—who also were working from home. Even when they got vaccinated and managed to hit the road, they often found that their customers’ doors were closed and they were not allowed inside, if their particular contact was there at all. Many times, they had to resort to meeting their customers in parking lots or restaurants with outdoor dining. And guess what? It’s not even over yet. So, how does a salesperson create success when so much seems to have changed? I reached out to Lee Salazar of Prototron to learn how he met the challenges, and his tips for others who are moving forward.

PCB Technologies' Subsidiary iNPACK to Exhibit at IMS Show

06/14/2022 | Andy Shaughnessy, I-Connect007
Jeff De Serrano, president of PCB Technologies USA, discusses the launch of their new company, iNPACK, which focuses on high-tech substrate technologies, microelectronics assembly, and electronics packaging. He details his plans to continue expanding InPack over the next year and to meet with customers and exhibit at the International Microwave Symposium Show in Denver June 19-24.

Copyright © 2022 I-Connect007. All rights reserved.