-
- News
- Books
Featured Books
- smt007 Magazine
Latest Issues
Current IssueBox Build
One trend is to add box build and final assembly to your product offering. In this issue, we explore the opportunities and risks of adding system assembly to your service portfolio.
IPC APEX EXPO 2024 Pre-show
This month’s issue devotes its pages to a comprehensive preview of the IPC APEX EXPO 2024 event. Whether your role is technical or business, if you're new-to-the-industry or seasoned veteran, you'll find value throughout this program.
Boost Your Sales
Every part of your business can be evaluated as a process, including your sales funnel. Optimizing your selling process requires a coordinated effort between marketing and sales. In this issue, industry experts in marketing and sales offer their best advice on how to boost your sales efforts.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - smt007 Magazine
Vapor Phase Technology is a Viable Solution, but Carries a Learning Curve
January 21, 2016 | Steve Fraser, FirstronicEstimated reading time: 6 minutes
In another case, the facility is producing large PCBAs used in flat panel monitors. In convection reflow soldering a large PCBA can see as much as 90°C variance in temperature from one end of the PCBA to the other as it moves through various zones. If all parts are sitting in solder paste, this doesn’t cause an issue; however, if balls aren’t touching paste this thermal mismatch can cause parts to pitch slightly and form a gas boundary which causes an oxidized "pillow" to form. The end result is that parts touch but don’t reflow. In VP reflow soldering the difference in temperature from one end of the PCBA to the other doesn’t exceed 2°C, eliminating the potential for this issue to occur. In this particular project, the facility achieved yields of over 99% in the first three days of production ramp-up and the project is running approximately 30,000 PCBAs per month.
There are some tradeoffs that can be easily dealt with once a team becomes familiar with the process and the technology. One technical challenge with VP reflow soldering is that the process can exacerbate 0402 and smaller device tombstoning. The solution is to incorporate a reverse home plate design for those pads on the stencil.
Another issue is the efficiency of the vapor blanket. In the 1970s and 1980s, when VP was still a common option, one of the negatives associated with VP technology was the fact that hybrid parts could be heat damaged. Sealed parts with open cavities could expand or explode. DC to DC or AC to DC converters (hybrid potted modules) would often fail. Today’s technology minimizes those parts, but profile optimization is important because both sides of the PCBA go into reflow instantaneously.
A key selling point of the technology is that the process windows are broad enough that few unique profiles are needed. However, there can be a learning curve in developing the right profile because of the speed at which reflow begins. For example, the engineering team once ruined a profiler because the process was set at a level where the electronics inside the mole reflowed while taking measurements.
The Cost Savings Equation
VP reflow technology can save cost in several ways. First, it uses less energy than convection reflow soldering systems, in part because it doesn’t radiate excess heat. It not only uses less energy, but the factory also requires less energy for cooling the air near the machine. For example in Mexico, where summer temperatures routinely exceed 100°F, VP is 40% an hour less expensive than use of a nine-zone convection reflow oven just in machine energy consumption alone. Add to that the fact that energy costs in Mexico are 1.5x higher than those in the United States and the additional savings associated with less radiant heat, and the concomitant load that places on air conditioning utilization, add up quickly.
Figure 3: X-ray image showing consistent ball shape and solder wetting from vapor phase reflow.
One area that adds cost is the fluid used to generate the vapor blanket since it is a consumable. However, the cost of the fluid is near or below the cost of nitrogen frequently used in convection reflow ovens.
One other area where VP reflow soldering technology can save money is on mixed technology PCBAs. When there are only a few through-hole parts, the PCBAs can often be completely soldered using pin-in-paste and VP technology. Depending on the product mix, this can eliminate or reduce the need for selective soldering systems or wave soldering machines.
Additionally, while wave solder is typically a 3 Sigma process, SMT reflow is a 5 Sigma plus process, which means that the SMT process is much more repeatable and controllable in volume production.
VP reflow soldering technology has matured to the point where it can easily support higher volume production requirements. The challenge is properly sizing the machine to likely workloads and optimizing the necessary profiles. The end result is improved quality, better line flexibility and lower energy consumption.
Read The Article In E-book Format
Editor's Note: This article originally appeared in the January 2016 issue of SMT Magazine.
Page 2 of 2Suggested Items
Indium Corporation Expert to Present on Pb-Free Solder for Die-Attach in Discrete Power Applications
04/30/2024 | Indium CorporationIndium Corporation Product Manager – Semiconductor Dean Payne will present at the Advanced Packaging for Power Electronics conference, hosted by IMAPS, held May 8-9 in Woburn, Massachusetts, USA.
Taiyo Circuit Automation Installs New DP3500 into Fuba Printed Circuits, Tunisia
04/25/2024 | Taiyo Circuit AutomationTaiyo Circuit Automation is proud to be partnered with Fuba Printed Circuits, Tunisia part of the OneTech Group of companies, a leading printed circuit board manufacturer based out of Bizerte, Tunisia, on their first installation of Taiyo Circuit Automation DP3500 coater.
Vicor Power Orders Hentec Industries/RPS Automation Pulsar Solderability Testing System
04/24/2024 | Hentec Industries/RPS AutomationHentec Industries/RPS Automation, a leading manufacturer of selective soldering, lead tinning and solderability test equipment, is pleased to announce that Vicor Power has finalized the purchase of a Pulsar solderability testing system.
AIM Solder’s Dillon Zhu to Present on Ultraminiature Soldering at SMTA China East
04/22/2024 | AIMAIM Solder, a leading global manufacturer of solder assembly materials for the electronics industry, is pleased to announce that Dillon Zhu will present on the topic: Ultraminiature Soldering: Techniques, Technologies, and Standards at SMTA China East. This event is being held at the Shanghai World Expo Exhibition & Convention Center from April 24-25.
AIM to Highlight NC259FPA Ultrafine No Clean Solder Paste at SMTA Wisconsin Expo & Tech Forum
04/18/2024 | AIMAIM Solder, a leading global manufacturer of solder assembly materials for the electronics industry, is pleased to announce its participation in the upcoming SMTA Wisconsin Expo & Tech Forum taking place on May 7 at the Four Points by Sheraton | Milwaukee Airport, in Milwaukee, Wisconsin.