Empowering the Workforce Through Training: An Investment Return


Reading time ( words)

Training is not shiny nor romantic. It doesn’t make the front page of the magazine, it’s not candy apple red, and, unless your executive team is enlightened, it can be a hard sell in the board room. However, lack of a robust and effective training program leads to underutilization and frustration.

Electronics manufacturers should take training seriously at all levels. To remain viable and competitive, it’s vital that they keep up with the latest technologies and practices in the electronics field. Perhaps more importantly, investment in employees keeps them engaged and excited in the performance of their daily work. People need growth to avoid stagnation and burnout. Learning new methods and being exposed to new ideas is pivotal to personal growth. A company is, at its foundation, little more than the people that work there. They are responsible for its gains or its declines. The stronger the foundation, the better to build upon.

MC Assembly has always been quick to recognize the need for up-to-date equipment and tooling in the pursuit of quality, throughput, and flexibility. The investment for equipment is often substantial and often, too little thought is given toward maximizing the productivity of capital expense. We leverage the opportunities provided us by our suppliers. The Florida facility runs multimillion dollar Universal Instruments surface mount lines. When buying these lines, we set aside monies to be used in training. That means sending engineers or maintenance personnel for training at their facility in Binghamton, New York, or bringing their trainers to our facilities to work with groups of operators on the production floor. It greatly increases our chances of using our equipment to its full potential. Likewise, we are in the process of upgrading our Aegis MES software package (FactoryLogix) and have scheduled multiple tiers of training for engineers, process writers, and operators who will be using the application.

With the help of a valued partner, Incito Consulting, we have recently completed, in our Florida and Massachusetts facilities, Incito Man training for all employees in addition to 150 employees that received this training in our Mexico facility. This program is an introduction to product flow, value stream mapping, and Lean manufacturing. Incito Man is a combination of classroom study and live, hands-on simulation. We train in groups of 25 employees selected from a variety of departments. They start in a classroom environment where they are given the basics of Lean. Then they’re brought into the live simulation room where they are instructed that they have to build 30 robots out of Legos in 15 minutes. The process they are given is heavily constrained and flawed.

Fig1_MCAssembly_Aug2017.jpg

Figure 1: MC Assembly’s Mexico facility team undergoing government certified electronics training course.

After 15 minutes, the employees have built somewhere between zero and three units. Often, there are defects in these units and employees are convinced that this is an impossible task. We review what went wrong and what went right with the round.

The responses vary, but typical themes are that the “stockroom personnel” are disorganized and that additional personnel are needed. The employees go back into the classroom and are shown how progressive build and better flow can yield higher quality product and more volume. Employees are shown the basics of creating a value stream map and will map out the Incito Man build. Meanwhile, the simulation has been reset and the employees are turned loose once again to attempt to build 30 robots in 15 minutes. They can move some of the processes, eliminating or reducing some constraints.

During this round, we typically get 10 to 12 units to our customer. As a group, we review cycle times and takt time requirements for the second round and discuss what went better during that round and what has yet to be improved. The third classroom session involves 5S organization and visual identification of product status. All constraints are removed for the third round and employees can reorganize the entire process.

It’s common that, by this time, the employees have streamlined the process to the point where they are able to free up some resources and build using less personnel (remember in the earlier rounds, when they thought that adding personnel was the solution?). Those that have been freed up from their tasks are assigned a “development project” building Lego dragons. The simulation is restarted and we nearly always get all 30 robots to the customer as well as five to 10 Lego dragons. Aside from being a great team building exercise, we’ve given the employees basic tools to make their job easier and their workplace, more efficient. Most employees can’t wait to get back to the shop and employ some of their new skills. It generates a ton of excitement for continuous improvement.

Several of our suppliers and customers have sent their own employees to participate in the Incito Man training alongside MC Assembly’s employees. Through this training, we hope to promote understanding and help bring up the level of those who provide service to us.

Incito Man training is given to all employees, as Lean can be applied to all aspects of our business. However, much of our training is more specialized depending on the employee’s job function. We provided Excel training for our production control, manufacturing supervisors, and process data management personnel. Although many of these employees had a firm grasp on the basics of Excel, they lacked some of the advanced training that allowed them to more fully use the software package and create shortcuts to make their job more efficient. Based on need, several went on to even more advanced training where they learned how to create macros and graph data for analysis purposes.

Fig2_MCAssembly_Aug2017.jpg

Figure 2: MC Assembly’s Mexico facility team with their certificates of completion from the electronics course.

We have multiple certified instructors of IPC and J-Standard on staff. They conduct classes to certify inspection and soldering personnel on site. Recertification is performed as required and the trainers are an available resource for clarification. They reinforce, daily, what trainees have been taught.

Share



Copyright © 2017 I-Connect007. All rights reserved.