Tips to Improve Soldering Tip Life and Reduce Cost


Reading time ( words)

Whether in production, or repair and rework, the cost of soldering iron tips can be easily overlooked, but with today’s requirement for higher temperatures in lead-free solder applications, the consumption of tips has dramatically increased. This fact, combined with changes in tip design to meet the higher thermal load requirements, has also resulted in escalating tip costs, making tip care a high priority.

In short, higher melting temperatures have resulted in:

  • The requirement for soldering irons to provide higher thermal performance
  • Shorter tip life due to the increased temperature/thermal load
  • Faster oxidation of tips due to the increased temperature

However, there are ways to improve tip life and reduce cost. Some key points to remember when soldering include the following:

  1. When not using the soldering iron, turn the power off. Accessories such as “sleep work stands” or “power down” functions will certainly help tip life but turning the power supply off when not in use will help even more.
  2. If using a sponge, do not oversoak it. Remember that every time the tip touches the sponge, a thermal shock occurs, potentially damaging the plating (e.g., if cold water is applied to hot glass, cracks occur).
  3. Do not use pliers to remove the tip. Undue pressure can easily deform tips. Use the tip removal pad.
  4. Make sure the tip is tinned with solder at all times. Solder helps protect the iron plating and prevent oxidization. A burnt or blackened tip will not take solder.

Suggested Tip Care Procedures

thermaltronics.jpgThe solder tip needs to be cleaned and tinned whenever the soldering iron is not in use. Tip life on soldering irons that have very fast thermal response, such as Thermaltronics Curie Heat Technology Soldering Irons, can be extended, if the following procedures are followed:

Procedure #1: Tin the tip before putting it into storage.

1. Turn off power supply.
2. Clean tip with brass curls.
3. Tin tip with solder.
4. Replace the hand piece in the work stand.

Note: It is recommended to turn the power supply off before cleaning the tip for storage. This will reduce the oxidation while performing maintenance of the tip with brass curls.

Procedure #2: Always keep the tip tinned when in use.

1. Select right size tip geometry for the joints being soldered. Ideally, it should be the largest possible size necessary to accomplish a good solder joint.
2. Do not apply too much force on the tip during soldering.
3. Use brass curls to clean the tip because this is better than a water-soaked sponge.
4. Use a soft brass brush for tough oxidation buildup or whenever brass curls may have difficulty in removing the oxidation from the tip surface.
5. Use tip tinner. Thermaltronics tips have more plating on the working end of the tip and this extra plating allows operators to use tip tinner/cleaner (TMT-TC-2) to restore tip life.

Note: When iron plating is exposed to water and oxygen, it corrodes. Oxidation is a chemical process that is caused by the interaction between oxygen and other elements that come from all kinds of fluxes, water, etc.

Suggested Tip Care Recovery Procedure

A) For heavily oxidized tips, the following procedure should be followed:

  1. Turn off the power supply.
  2. Dip the tip in the tip tinner/cleaner.
  3. Brush tip with a soft wire brush to clean off the oxide layer. (Repeat the process if the tip is badly burnt/oxidized.)
  4. Re-tin the tip and return to the stand.

Note: Most soldering tips operate at 375˚C+ and since the typical lead-free solder wire melt temperature is ±217˚C, there is still sufficient thermal energy left in the tip to complete the above process. If power is left on during the cleaning process, the power supply will drive more thermal energy to the tip and try to heat the tip tinner or wire brush.

B) If the tip is not badly oxidized but is still in need of cleaning:

  1. Turn off the power supply.
  2. Dip the tip in the tip tinner/cleaner.
  3. Use brass curls to clean off the oxide.
  4. Repeat as needed.
  5. Re-tin the tip and return to the stand.

C) For applications where a sponge is in use:

  1. Make sure the sponge is sulphur-free and designed for soldering use.
  2. Turn off the power supply.
  3. Do not oversoak the sponge: squeeze it to release excess water.
  4. Use deionized water—not tap water.
  5. Do not repeatedly use the spongewater is H2O and the oxygen part will add to potential oxidization.
  6. Once clean, tin tip and return to the stand.

If the above procedures are followed, tip life can be maximized.

About Thermaltronics

Thermaltronics is a manufacturer and supplier of a wide range of soldering products and accessories used in the electronics manufacturing industry. Design and development is undertaken in the USA and Australia, with final production taking place in a customised manufacturing facility, incorporating specialised equipment and in accordance with recognised international standards of quality and compliance.

In addition to the modern factory, Thermaltronics maintains an office and warehouse in New York State, commercial offices in Hong Kong, and a Distribution Sales Office in Perth, Australia.

Thermaltronics embraces both strict quality control and conformance with International Manufacturing Standards, is in compliance with ISO 9000 and ISO 14000 and holds certification in TuV, GS, NRTL & CE. Product warranties are among the best in the industry and distribution of the company’s products is available worldwide. For further information, click here.

Share

Print


Suggested Items

How to Benefit From Robotic Soldering Processes

10/28/2020 | Pete Starkey, I-Connect007
Webinars are in vogue! But in Pete Starkey's experience, the master of the technical webinar with many years’ experience of delivering first-rate events is Bob Willis—electronics assembly specialist, soldering expert, and provider of training and consultancy in electronics manufacture. Here, Pete recaps Bob’s presentation on the upcoming robotic soldering experience.

90% Solder Dross Recovery: Eliminate Waste, Save Money

10/20/2020 | Nolan Johnson, I-Connect007
The impact of 90% solder dross recovery can have a substantial impact on reducing waste and increasing cost savings. Nolan Johnson recently spoke with Jay Hardin, MS2® product manager at P. Kay Metal, about the process and benefits of efficient solder dross recovery, as well as product roadmaps, the soldering machine market, and raw materials supply chain for solder alloy manufacturing. As Jay says, “For many companies, the savings are in the thousands or millions” of dollars.

Real Time with… SMTAI 2020: Reflections on the Technical Conference

10/07/2020 | Real Time with...SMTAI
This year’s SMTA International Conference and Exposition went virtual! Pete Starkey explains how the SMTA team did a fine job in difficult circumstances to present an interactive show and technical conference. Here, he highlights four of the papers that particularly caught his interest.



Copyright © 2020 I-Connect007. All rights reserved.