New Die Attach Adhesive from DELO Offers Strong Adhesion After Aging, Flexibility in Dispensing Method

Reading time ( words)

DELO, one of the world’s leading manufacturers of industrial adhesives for automotive, consumer and industrial electronics applications, has launched a new die attach adhesive that offers high strength after aging. According to tests performed in conjunction with the machine integrator, ASM Assembly Systems, a global manufacturer of SMT placement machines and solutions, DELO MONOPOX EG2596 can be dispensed more precisely than its predecessor, DELO MONOPOX MK096. This new fluorescent adhesive is suitable for long-term use in semiconductor and surface mount technology applications.

Technical Specifications

  • High strength after aging
  • Precise dispensing
  • Suitable for long-term use
  • Thixotropy index of ~ 9
  • Drop sizes down to below 250 µm can be achieved
  • Curing takes place in 10 minutes at +130 °C

Suited for long-term use
DELO MONOPOX EG2596 can be used on printed circuit boards to fix components, and act as electrical insulation. It is temperature-resistant and offers good dispensing properties, meeting the increasing miniaturization requirements in today’s electronics.

Suited for long-term use, this new, heat-curing, one-component epoxy resin adhesive exhibits a 150% higher strength after seven days of storage at 85% relative air humidity and a temperature of +85 °C. DELO MONOPOX EG2596 maintains strong adhesion even after typical aging tests, like the MSL1 test, in accordance with JEDEC standard. When using 1x1 mm² silicon dies, the test revealed adhesion values of 47 N on FR4 substrate and 62 N on gold.

Excellent flow-resistant dispensing pattern
DELO MONOPOX EG2596 has a high thixotropy index of ~ 9. The higher the index value, the more flow-resistant the dispensing pattern will be after the dispensing process. The thixotropic properties of this die attach adhesive ensures that it can be applied very finely in a low-viscous state because of the shear in the dispensing valve. 

After dispensing, viscosity increases again in fractions of a second, preventing the resin from flowing. This allows the adhesive to be built up in individual droplets and then shaped in a controlled manner, without it spreading into areas that should remain adhesive-free. Even during heat curing, the adhesive drop remains dimensionally stable.  

The flow properties of DELO MONOPOX EG2596 are designed to allow dispensing by jet valves and needles. Thanks to this flexibility, the adhesive provides versatile application options. Tests conducted jointly by DELO and its technology partner, ASM Assembly Systems, show the excellent dispensing properties of the die attach adhesive using, among other dispensing systems, the ’Glue Feeder’. This jet valve allows the adhesive to be dispensed contactless and upside down. The adhesive is applied directly to the specific component and not to the printed circuit board. This solution ensures fast and highly precise processes. 

Depending on the dispensing equipment, drop sizes down to below 250 µm can be achieved. Even after several shots, dispensing patterns remain uniform and do not show typical unwanted effects, like satellite droplets. 

Curing takes place in 10 minutes at +130 °C. The fluorescent adhesive is available in 10 cc cartridges and can be ordered in quantities of just one. Once opened, the product can be processed in a user-friendly manner for up to seven days in a standard climate of +23 °C.



Suggested Items

SMTA Europe Solder Finish Webinar Addresses Defects Causes and Cures

12/14/2020 | Pete Starkey, I-Connect007
“What is your most common PCB problem?” A survey conducted by Bob Willis had revealed finish solderability to be the predominant contender, and it was clear that the choice of solderable finish applied to surface mount boards could have a significant effect on the assembly yield and cost of the final circuit. SMTA Europe organised an informative and enlightening webinar this month entitled “Guide to PCB Solder Finishes—Process Defects Causes and Cures,” with soldering specialist Bob Willis as presenter.

SMTA Europe Webinar: What Is a Good Solder Joint, and How Can Solder Joints Be Tested?

11/18/2020 | Pete Starkey, I-Connect007
What is a good solder joint? And how can they be tested not only for purposes of process characterisation, optimisation, monitoring, and control but also for ensuring their long-term reliability? Pete Starkey details a webinar organised by the Europe Chapter of SMTA that was presented by Bob Willis, an expert in soldering, assembly technologies, and failure analysis.

Reducing Flux Splatter in Sensors and Camera Modules

10/30/2020 | Jasbir Bath, Shantanu Joshi, and Noriyoshi Uchida, Koki Solder America And Koki Company Limited
With the increased use of electronics in new technology areas, flux formulations are being developed to address the new and existing requirements. For sensors and camera modules used for Advanced Driver Assistance System (ADAS) and internet of things (IoT) applications, there is a demand for no-clean flux formulations in lead-free solder paste, which can reduce flux splattering during reflow.

Copyright © 2021 I-Connect007. All rights reserved.